电梯门套收口做法通常包括以下几个步骤：

　　The method of closing elevator door frames usually includes the following steps:

　　处理墙面不平处 ：确保墙面平整，并清理灰尘。

　　Handle uneven areas on the wall: Ensure that the wall is flat and clean up dust.

　　中心定位 ：根据电梯安装要求，进行中心定位，并弹线以确定门套位置。

　　Central positioning: According to the installation requirements of the elevator, perform central positioning and mark the line to determine the position of the door frame.

　　安装门套基层 ：使用大芯板作为基层，用木条和木楔子固定，竖向间距控制在100mm—200mm之间，边口用细木条塞缝。

　　Installation of door frame base: Use a large core board as the base, fix it with wooden strips and wedges, and control the vertical spacing between 100mm and 200mm. Use thin wooden strips to fill the gaps at the edges.

　　剪裁和包边 ：根据门套尺寸剪裁线条，并进行45度斜切处理，使其圆润美观。使用专用包边条将多余部分包裹，留出伸缩缝。

　　Cutting and edging: Cut the lines according to the size of the door frame and perform a 45 degree oblique cut to make it rounded and beautiful. Wrap the excess part with a dedicated edging strip, leaving expansion joints.

　　固定骨架 ：在墙体上打孔，预埋膨胀螺栓，将不锈钢电梯门套线条的骨架安装在墙体上。

　　Fixed skeleton: Drill holes on the wall, embed expansion bolts, and install the skeleton of stainless steel elevator door frame lines on the wall.

　　安装门套 ：将制作好的门套线条安装在墙体上，并确保线条完全覆盖门洞上方部位，预留伸缩量。

　　Install door frame: Install the pre made door frame lines on the wall and ensure that the lines completely cover the area above the door opening, leaving room for expansion and contraction.

　　填充缝隙 ：使用发泡剂填充门套与墙体之间的缝隙，确保密封。

　　Fill the gap: Use foaming agent to fill the gap between the door frame and the wall to ensure sealing.

　　安装门扇 ：将电梯门安装到门套上，确保合页位置准确，门与门套的间隙控制在1.5mm以内，以保证顺畅开关门。

　　Install door leaf: Install the elevator door onto the door frame, ensuring accurate hinge position and controlling the gap between the door and the frame within 1.5mm to ensure smooth opening and closing of the door.

　　质量检查 ：检查安装后的门套是否牢固、准确、稳定，并进行必要的修整。

　　Quality inspection: Check whether the installed door frame is firm, accurate, and stable, and make necessary adjustments.

　　以上步骤完成后，电梯门套收口工作基本完成。请根据具体情况调整施工细节，并遵循相关施工规范和安全标准

　　After completing the above steps, the elevator door frame closing work is basically completed. Please adjust the construction details according to the specific situation and follow relevant construction specifications and safety standards

　　本文来自：淄博电梯门套厂家更多的内容请点击：http://www.sddtmt.com我们将会为您提问的问题提供一个满意的服务，欢迎您的来电！

　　This article is from Zibo Elevator Door Frame Manufacturer. For more content, please click: http://www.sddtmt.com We will provide satisfactory service for the questions you ask. Welcome to call us!